|
Related Topics:
| TECH: Domino Man blows xformer fuses when PCB plugged in - Hey all, I've got a Domino Man I've been working on restoring since buying a converted cabinet last summer. It's almost and I received the last major piece, the pcb, today. The 90412 seems to be putting out good +5 and +12..
tech: composite vs seperate sync - Hi all I just dragged in a couple of my old Commodore 1084S monitors to use with my supergun (on my bench, as opposed to dragging PCBs over to the C128 setup) One of them has a blown flyback :( The other is a different 1084S, and only offers analog RGB.
Tech: Food Fight sync - All, I am having trouble getting a every food fight board I have is unable to sync on a test bench monitor. It is a commodore 1084s. All other games sync fine and the food fights do sync on normal monitor. Any ideas? Anyone ever had this same issue?
Tech: WGK4900 Sync question/cap kit gone wrong? - I had a 4900 standard res monitor that had a picture, but needed a cap kit. I installed a cap kit last night, and when I fired it up, I got a picture, but it was collapsed (line down the center) and the sync was off. After a couple of seconds, I..
Tech: Can you give me your DEFENDER monitor sync info? - Well, I've tried about three and still have defender on the screen. I'm not sure if the monitor is the original, it's a Wells Gardner 19K4951. there's a 6 pin, and a 3. So on the 6, I've got: red green blue ground empty empty And..
|
|
| Author |
Message |
External
Since: Jan 02, 2008
Posts: 3
|
(Msg. 1) Posted: Tue Feb 05, 2008 3:27 pm
Post subject: TECH: Domino Man sync on a G07
Archived from groups: rec>games>video>arcade>collecting (more info?)
|
|
|
Hey all,
I've got a Domino Man that I can't get to sync horizontally or
vertically on a G07. I'm using Bob's replacement MCR cable and
plugging the 3 pin sync connector to the 3 pin negative sync plug on
the G07. Shouldn't this be correct or are MCRII games not negative
sync? Also, I tried moving the connector 1 pin to the left and then
the horizontal sync would lock in but not the vertical. Perhaps I
should try swapping the wires? I also thought I read in the archives
about needing to sometimes using a jumper to get the games to sync
properly? Any thoughts on this are appreciated. My gut tells me to
swap the 2 sync wires, but I thought I'd get some confirmation before
I do that. Perhaps the connector from Bob is made for another monitor
that came with Tron or other MCR games? |
|
| Back to top |
|
 | |
External
Since: Dec 07, 2007
Posts: 8
|
(Msg. 2) Posted: Tue Feb 05, 2008 5:39 pm
Post subject: Re: TECH: Domino Man sync on a G07 [Login to view extended thread Info.]
Archived from groups: per prev. post (more info?)
|
|
|
On Feb 5, 6:27 pm, Bill <miekk....RemoveThis@msu.edu> wrote:
> Hey all,
>
> I've got a Domino Man that I can't get to sync horizontally or
> vertically on a G07. I'm using Bob's replacement MCR cable and
> plugging the 3 pin sync connector to the 3 pin negative sync plug on
> the G07. Shouldn't this be correct or are MCRII games not negative
> sync? Also, I tried moving the connector 1 pin to the left and then
> the horizontal sync would lock in but not the vertical. Perhaps I
> should try swapping the wires? I also thought I read in the archives
> about needing to sometimes using a jumper to get the games to sync
> properly? Any thoughts on this are appreciated. My gut tells me to
> swap the 2 sync wires, but I thought I'd get some confirmation before
> I do that. Perhaps the connector from Bob is made for another monitor
> that came with Tron or other MCR games?
MCR games are positive sync. |
|
| Back to top |
|
| |
|
FAQ
Search
Profile
Private Messages
Log in/Register/Password
